SEAL-KRETE® High Performance Floor Coatings, Color-Shell Concrete Stain, Terra Cotta, 16 oz.
*While supply lasts/Item being Discontinued
Seal-Krete® Color-Shell utilizes the latest in UV stable colorant technology offering a fast drying easy to apply concrete stain. Color-Shell creates unique, multi-colored translucent colors that will not peel, chip, or flake. Available in 20 standard colors which can be combined to create unlimited color possibilities. When properly sealed Color-Shell will resist staining and harsh chemicals.
NOTE: On-screen and printed color representations may vary from actual color once applied to concrete. Recommended to test an inconspicuous area before applying to the whole area.
*Limited stock available
- Concrete stain
- Variegated finish
- SCAQMD approved stain
- 20 Standard colors availble
- Ulimited possibilities of colors
- Fast drying - Topcoat in 1 hour
- Acid free
- Will not peel or flake
- Gloss and Matte Topcoats available
- Restaurant Floors
- Entry Ways
- Bar Floors
- Patios and Walkways
- Basement Floors
- Garage Floors
- Concrete Paver Refresh
- Stamped Concrete
- Retail Stores
- Showrooms
| Special Offers | Discontinued |
|---|---|
| Series/Sub-Brand | Seal Krete |
| Type | Interior/Exterior |
| Size | 16 oz. |
| Color | Terra Cotta |
| Brand | Seal Krete |
| Color Family | Red |
| Material | Concrete Stain |
| Manufacturer Code | 980014 |
Application: Apply when temperature is 40°F to 85°F. Do not apply if water or ice is present. Do not apply to slabs on grade unless a heavy uninterrupted vapor barrier has been installed under the slab. Do not apply if the floor Moisture Vapor Rating is higher than 3 lbs. per 1000 sq. ft.
NOTE: Test in an inconspicuous area before starting project to assure compatibility of all products and approval of color.
Color-Shell is ready for application as soon as it’s mixed with acetone. Use only an acetone resistant sprayer equipped with EPDM Seals like Chapin model #21127XP. Begin by spraying evenly and continuously over the prepared surface, using a #6 or #8 conical tip, in a circular motion. Do not allow Color-Shell to puddle. Mop up any excess with a clean rag so that the surface will dry evenly. During application keep end of tip at least 12-24 inches form substrate. This technique will insure that Color-Shell is fogged on resulting in a variegated look. Co2 based sprayers are recommended for large areas. These sprayers will offer constant even pressure. Avoid long straight runs to minimize striping. A second color can be applied right after or at the same time to create a multi-color or two tones finish.
IMPORTANT: If you need to stop during application, we recommend covering spray tip with a clean rag and or putting sprayer into a 5 gallon pail to avoid getting drips on the deck. Allow to dry 1 hour before sealing.
Mixing: Color-Shell Stain is packaged in liquid form and needs to be mixed with acetone. Please follow the Acetone manufacturer’s instructions and Safety Data Sheet (SDS) for safe handling and exposure limits.
Semi-Transparent Finish: Mix one bottle of ColorShell to one gallon of acetone and mix 30 seconds.
Deep Rich Finish: Mix one bottle of Color-Shell to one quart of acetone and mix 30 seconds.
Transparent Finish: Mix one bottle of Color-Shell to five gallons of acetone and mix 90 seconds.
DO NOT USE any type of electrical equipment to stir the product into the Acetone. Acetone is highly flammable and may ignite.
Clean-Up: Clean tools and sprayer immediately with acetone. Dried Color-Shell with require mechanical abrasion from the substrate to be removed. Do not use xylene in an acetone sprayer as its will dissolve the gaskets damage hose and tips.
Dry Time: To Touch 5 minutes, To Recoat 15 minutes, Top Coat 1 hour with 70-80°F (21-27ºC) and 50% Relative Humidity